Есть неизвестно чем убитый аппрарат
При включении Wait Image и следующий лог:
Кидаем прошивку получаем ответ:
Включаем режим Probe - и комп не видит принтер, после ввода команды ml 0x40020000 так же не видит.
Вводим команду FL определяет и орет что нет идентификатора оборудования.
ответ FL
Прошивка в режиме FL на любую версию, с небольшими отличиями выдает одно и тоже:
При включении Wait Image и следующий лог:
- Код: выделить все
n<0><0>
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
New kernel was found...
CHKSUM
{
check sum start address : 00040000, count : 00440000
check sum : 00006932
} /* Checksum End
Checksum Fail!!, original checksum = 0x0000A5A5, checksum = 0x00006932
finish copy image to the RAM
===> Now program restarted on the RAM to program flash
jump to 0x40020000
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
verify_Image : 0x41800000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG : $IMG
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
DrvUsbISP1761Initialize
Download destination Address : 0x41800000
Please send data via usb (ISP1761)!!!<FS><HS><FS><HS
Кидаем прошивку получаем ответ:
- Код: выделить все
[[14942232 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x41800000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00E40000
model : 0x05000021
flash type : 0x00020004
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 41800018, count : 00E40000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
Found new kernel(0x41840018)!!!!
ZIP Dest : 0x40B00000
[[[FFFFFFF8]]], [[[000F697F]]]
This is not a valid image.!!!!
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Agai
Включаем режим Probe - и комп не видит принтер, после ввода команды ml 0x40020000 так же не видит.
Вводим команду FL определяет и орет что нет идентификатора оборудования.
ответ FL
- Код: выделить все
pROBE+> fl
Upgrade Flash ROM Image
==> Now program restarted on the RAM to program flash ROM(0x40020000)
jump to 0x40020000
Flash Data Download Address : 0x41800000
===============================
Start flash_writer
===============================
verify_Image : 0x41800000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG : $IMG
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x41800000)
DrvUsbISP1761Initialize
Download destination Address : 0x41800000
Please send data via usb (ISP1761)!!!<FS><HS><FS><HS>
Прошивка в режиме FL на любую версию, с небольшими отличиями выдает одно и тоже:
- Код: выделить все
Image includes PJL(0000001B) -> Waste 48 bytes
[[14942232 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x41800000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00E40000
model : 0x05000021
flash type : 0x00020004
image type : 0x00000000
temp_buf : $IMG
SIG : $IMG
FlashCheckSum
{
check sum start address : 41800018, count : 00E40000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
Found new kernel(0x41840018)!!!!
ZIP Dest : 0x40B00000
[[[FFFFFFF8]]], [[[000F697F]]]
This is not a valid image.!!!!
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again