Здравствуйте! Помогите пожалуйста! Клиент побывал сам пере прошить, заливал бесплатный фикс прошивка не удалась, опять прошивал с заклеенным чипом)) после этого принес ко мне. Принтер выходит в готовность и определяется, решил залить оригинальную прошивку, но она полностью не заливается, на второй строчке зависает.Спаял Debug вот что он мне выдал! Как все это исправить?
- Код: выделить все
Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
Kernel Data Read End
Compressed Kernel was found (0x02000000)...
Decompressing Kernel to RAM
src_addr = 0x0200000C, dest_addr = 0x00100000, ul_size = 0x0068AC00
Decompress ...................................................................................................................................................................................................................................................................................... Done
Kernel Start [0x00100000]
FW Upgrade JUMP : 0088F954
RootWriteMonitorProgram : 000101C4
Serial Init for polling msg. sysHwInit : 647
hardWareInterFaceInit
[wifiEndDrvPlug] enter
[wifiEndDrvPlug] end
miiBusModeSet Error
sysHwInit2 752
sysHwInit2 759
Host Name: bootHost
Target Name[: vxTarget
User: target
wifiEndStart ] start
[wifiEnd] Link Up
[wifiEndStart ] end
Instantiating /ram as rawFs, device = 0x1
Formatting /ram for DOSFS
Instantiating /ram as rawFs, device = 0x1
Formatting...Retrieved old volume params with %38 confidence:
Volume Parameters: FAT type: FAT32, sectors per cluster 0
0 FAT copies, 0 clusters, 0 sectors per FAT
Sectors reserved 0, hidden 0, FAT sectors 0
Root dir entries 0, sysId (null) , serial number 10000
Label:" " ...
Disk with 64 sectors of 512 bytes will be formatted with:
Volume Parameters: FAT type: FAT12, sectors per cluster 1
2 FAT copies, 54 clusters, 1 sectors per FAT
Sectors reserved 1, hidden 0, FAT sectors 2
Root dir entries 112, sysId VXDOS12 , serial number 10000
Label:" " ...
OK.
ExceptionCheckMessage
====================== Check Boot [0xffffffff]
//////////////////////////////////////////////////////////////
// VxWorks Stack Remain for Kernel..
// VxWorks Stack Free = (0039afd0)
//RAM_LOW_ADRS = 00100000
//sysPhysMemTop = 04000000
//sysMemTop = 01e80000
//////////////////////////////////////////////////////////////
«< Reelase Mode »>
«<LogMsg_PrintOff»>
FFDrv_CheckInstall 1
pDCB->ulSPINo 0
pDCB->ulSlaveDevChannel 0
«<LogMsg_PrintOff»>
«<LogMsg_EngPrintOff»>
Model Code : SCX3405W
Main Kernel F/W Version : V3.00.01.10
Main Kernel F/W Date : JAN-23-2012
DRAM:>
«<HAL_InitWDT»> WatchDog Initialized !!!
Check PowerOn Mode PBA Port —— ( GPIO1Ctrl - 0xde73c006 GPIO1Dir - 0x868cfff9 GPIO1In - 0xee04dfc2 )
Check PowerOn Mode PBA Port —— ( GPIO2Ctrl - 0xfb446b7f GPIO2Dir - 0xe22400 GPIO2In - 0x1cefa000 )
################### Normal Mode Start##########################
PrnVPUDrv Driver is Installed successfully
PrnVPUDrv Driver:Create and Added Device to DM(Handle=16297788)
[WLAN] NVRAM : SEC
ipd: kill ipdhcpc failed: not found
ipd: start ipdhcpc6 ok
======NICCON Init Finish!!=========
*********************************************************************
[ImTMAA_RegisterItems] Error... JBIG ENC/DEC Function Needed...
*********************************************************************MT1900 Task Mode is 1
WLAN_BCM_P2P_Initialize 152
USB Port ON
Warning!!
Warning!!
[ConAdmin] Mem Alloc Size (204800), Avail (54784) in /home2/gv3system/swaroop.jr/Egmont/Jan23/GV3_System/GV3_Source/Subsystem/ConSS/App/ConIDS/IDS_Main.c 229 line
===»> CJI_IF_PSH_GCPSetBusyState [0]10M Half Duplex
======WSD Init Finish!!=========
