Здравствуйте. Имею аппарат с симптомами кривой прошивки.При включении красный глаз, мотор не крутит - полная тишина. Только слышно когда переходит в режим сна и из него (щелчёк).
PrinterInfo пишет:
- Код: выделить все
Model Name : M262x 282x Series
Machine Serial Number : ZD1UBJCD5000GWN
Host Name : SEC001599E71FAF
System Firmware Version : V3.00.01.33 MAR-10-2016 (M2820ND)
Product Information
Country : RUSSIA
Customer Support : www.samsungprinter.com
Supplies Number :
Installed Date : 2015-06-03
H/W Configuration
Duplex Unit : Installed
Capabilities
RAM : 128 MB
Tray 1 : 250
Software Versions
System Firmware Version : V3.00.01.33 MAR-10-2016 (M2820ND)
Engine Firmware Version : V1.00.12 08-11-2015
Network Firmware Version : 31.03.60_0.1_13-11-18
IP Core Version : 31.03.60_0.1_13-11-18
SPL Version : SPL 5.73.04 06-10-2014
PCL5E Version : F7.67.01 01-15-2016
PCLXL Version : F9.00.12 07-10-2015
Quality Control Versions
EP Version : V1.8
Fuser Version : V1.60
TR Version : V1.8
Print CMS Version : V0.2F
Product Setting
Language : English
Sleep Mode : 1 min.
Auto Power Off Mode : Off
Paper Setting
Media Name : Tray 1
Paper Type : Plain
Paper Size : A4
Media Name : Manual Feeder
Paper Type : Plain
Paper Size : A4
Print Setting
Auto Continue : 0 second(s)
Toner Save Mode : Off
Altitude Adjustment : Normal
Paper Substitution : Off
General Information
Total Impressions : 21095
Toner Information Black
Model ID :
Life Remaining : 0%(P0.0)
Impressions (Remaining) : 0(0%)
Serial No. :
Supplier :
Product Date : YYYYMMDD
First Installed Date : YYYYMMDD
Last Used Date : YYYYMMDD
Equivalent Pages Printed : 0
Estimated Pages Remaining : 0
Dot Count (Remaining) : 0(0%)
Company ID :
Supplier ID :
Capacity : 0.0K
Version : 0
Real Used Dot Count : 0
Clear Worn Message : 0
Impressions After Worn : 0
New Toner Count : 0
Kind of Cartridge :
Как видно инфо о чипе отсутствует. Чип менял на новый. Колодка крам подключена, прозвонил.
Подключил дебаг:
- Код: выделить все
Ver.1.12 New 2013-09-26
A1500
BOOT STATUS(MaskRom:1, SecBoot:1, Media:SPI)
DRAM: 127 MiB
Now running in RAM - U-Boot at: 07800000
malloc start 073fe000, end 07800000, size 00402000
Using default environment
Board: samsung,a1500_srpm4
Hit any key to stop autoboot: 0
a1500_kingbird # %^▒abcd
Ver.1.12 New 2013-09-26
A1500
BOOT STATUS(MaskRom:1, SecBoot:1, Media:SPI)
DRAM: 127 MiB
Now running in RAM - U-Boot at: 07800000
malloc start 073fe000, end 07800000, size 00402000
Using default environment
Board: samsung,a1500_srpm4
Hit any key to stop autoboot: 0
[[[[[ VERIFY : SIG: $NKF, BASE : 0x120000, 0x50fff4]]]]]
Kernel loader Ver : 0.12 :
5-a
3-g3
Loading kernel (rom 0x00040000) image.....OK
Run kernel 0x00120000 ....
Kernel loader Ver : 0.12 : 7--> Uart Initialize
--> InitCacheLib
--> StartMMU
--> EnableCache
--> Interrupt_Initialize
--> spgpMpIntDevInit
--> TxSetIntHandler
--> sysClkEnable
[WARNNING]Timer5 is not running? check it!!*
Now, tx_kernel_enter ...
==> tx_application_define
ExceptionCheckMessage
----- I2C PIN SELECT --------------
0x00888880
0x00888880
-------- A1500 -----------
====================== Check Boot [0x0]
************************************
* System Information *
************************************
[tfKernelInitialize]
<<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
FFDrv_CheckInstall 1
pDCB->ulSPINo 0
pDCB->ulSlaveDevChannel 0
<<<HAL_InitWDT>>> WatchDog Initialized !!!
<<<LogMsg_PrintOff>>>
<<<LogMsg_EngPrintOff>>>
=============== ESCMS =================
[CTS Ver: Kingbird-N EP V1.8]
[CTS Ver: Kingbird28_C3N FUSER V1.60]
[CTS Ver: Kingbird-N PRINT V0.2F]
[CTS Ver: Kingbird-N TR V1.8]
[CTS Ver: KingbirdN_MOTER V0.01]
========================================
Model Code : M2625M2825
Main Kernel F/W Version : V3.00.01.33
Main Kernel F/W Date : MAR-10-2016
<<<PrnEngIF_EngineEntry>>> Calling Enry...(0x7ca0d360)
PBA Mode 32768 2
################### Normal Mode Start##########################
<<<PrnCounter Cru>>> All-in-one Type !!!!
[ConAdmin] (WLANDRV_IF_GetP2PPinNumber) There is no Specific function in table
No carrier sense - Check network cable.
MT1900 Task Mode is 1
=======================================================================================
Log Count : 00000000-00000000-00000000-00000000-00000000-00000000-00000000-000000
=======================================================================================
!!! kernel_main END!!!
======NICCON Init Finish!!=========
====== Network Ready 8======
======WSD Init Finish!!=========
С нажатой "N" в терминале, после ввода команды "fl":
- Код: выделить все
Ver.1.12 New 2013-09-26
A1500
BOOT STATUS(MaskRom:1, SecBoot:1, Media:SPI)
DRAM: 127 MiB
Now running in RAM - U-Boot at: 07800000
malloc start 073fe000, end 07800000, size 00402000
Using default environment
Board: samsung,a1500_srpm4
Hit any key to stop autoboot: 0
a1500_kingbird # fl
serial flash upgrade...
Download Image from PC
{
phy init ok
SNPSID : 0x5533202a
....Done.SUPER SPEED
FULL SPEED
FULL SPEED
FULL SPEED
FULL SPEED
FULL SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
Тоже самое с зажатой кнопкой "стоп" при нажатии кнопки "ВКЛ"
Дальше когда кидаю прошивку на usbprns2:
- Код: выделить все
Ver.1.12 New 2013-09-26
A1500
BOOT STATUS(MaskRom:1, SecBoot:1, Media:SPI)
DRAM: 127 MiB
Now running in RAM - U-Boot at: 07800000
malloc start 073fe000, end 07800000, size 00402000
Using default environment
Board: samsung,a1500_srpm4
Hit any key to stop autoboot: 0
a1500_kingbird # fl
serial flash upgrade...
Download Image from PC
{
phy init ok
SNPSID : 0x5533202a
....Done.SUPER SPEED
FULL SPEED
FULL SPEED
FULL SPEED
FULL SPEED
FULL SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
HIGH SPEED
Image includes PJL(1b) -> Waste 92 bytes
[[8388636 Bytes received 0x0090001c - 0x00100000]] - Complete Downloading
} /* Download End */
[[[[[ HEADER : SIG: $KER ]]]]]
firmware sig : $KER
firmware source addr : 0x00100000
firmware start addr : 0x00000000
firmware size : 0x00800000
major : 0x03000094
minor : 0x00030002
image bank : 0x00000000
FlashCheckSum
{
check sum start address : 10001c, count : 800000
check sum : a5a5
} /* Checksum End
Source Checksum is valid
Image with Boot Rom
Kernel loader Ver : 0.12 : 1
Kernel loader Ver : 0.12 : 1
Kernel loader Ver : 0.12 : 1
Kernel loader Ver : 0.12 : 1
[[[[[ Flash Writing : SIG: $KER, BASE : 0x0, 0x800000]]]]]
0x10000 bytes programmed(1 % : 0x7f0000)...........
0xd0000 bytes programmed(10 % : 0x730000)............
0x1a0000 bytes programmed(20 % : 0x660000)............
0x270000 bytes programmed(30 % : 0x590000)............
0x340000 bytes programmed(40 % : 0x4c0000)...........
0x400000 bytes programmed(50 % : 0x400000)............
0x4d0000 bytes programmed(60 % : 0x330000)............
0x5a0000 bytes programmed(70 % : 0x260000)............
0x670000 bytes programmed(80 % : 0x190000)............
0x740000 bytes programmed(90 % : 0xc0000)...........
0x800000 bytes programmed(100 % : 0x0)
FlashCheckSum
{
check sum start address : 10001c, count : 800000
check sum : a5a5
} /* Checksum End
=>check sum is valid
resetting ...
Kernel loader Ver : 0.12 : 7
===Watch Dog Reset===
a1500_kingbird # <INTERRUPT>
a1500_kingbird # %^▒abcd
Ver.1.12 New 2013-09-26
A1500
BOOT STATUS(MaskRom:1, SecBoot:1, Media:SPI)
DRAM: 127 MiB
Now running in RAM - U-Boot at: 07800000
malloc start 073fe000, end 07800000, size 00402000
Using default environment
Board: samsung,a1500_srpm4
Hit any key to stop autoboot: 0
[[[[[ VERIFY : SIG: $NKF, BASE : 0x120000, 0x50fff4]]]]]
Kernel loader Ver : 0.12 :
5-a
3-g3
Loading kernel (rom 0x00040000) image.....OK
Run kernel 0x00120000 ....
Kernel loader Ver : 0.12 : 7--> Uart Initialize
--> InitCacheLib
--> StartMMU
--> EnableCache
--> Interrupt_Initialize
--> spgpMpIntDevInit
--> TxSetIntHandler
--> sysClkEnable
[WARNNING]Timer5 is not running? check it!!*
Now, tx_kernel_enter ...
==> tx_application_define
ExceptionCheckMessage
----- I2C PIN SELECT --------------
0x00888880
0x00888880
-------- A1500 -----------
====================== Check Boot [0x0]
************************************
* System Information *
************************************
[tfKernelInitialize]
<<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
FFDrv_CheckInstall 1
pDCB->ulSPINo 0
pDCB->ulSlaveDevChannel 0
<<<HAL_InitWDT>>> WatchDog Initialized !!!
<<<LogMsg_PrintOff>>>
<<<LogMsg_EngPrintOff>>>
=============== ESCMS =================
[CTS Ver: Kingbird-N EP V1.8]
[CTS Ver: Kingbird28_C3N FUSER V1.60]
[CTS Ver: Kingbird-N PRINT V0.2F]
[CTS Ver: Kingbird-N TR V1.8]
[CTS Ver: KingbirdN_MOTER V0.01]
========================================
Model Code : M2625M2825
Main Kernel F/W Version : V3.00.01.33
Main Kernel F/W Date : MAR-10-2016
<<<PrnEngIF_EngineEntry>>> Calling Enry...(0x7ca0d360)
PBA Mode 32768 2
################### Normal Mode Start##########################
<<<PrnCounter Cru>>> All-in-one Type !!!!
[ConAdmin] (WLANDRV_IF_GetP2PPinNumber) There is no Specific function in table
No carrier sense - Check network cable.
MT1900 Task Mode is 1
=======================================================================================
Log Count : 00000000-00000000-00000000-00000000-00000000-00000000-00000000-000000
=======================================================================================
!!! kernel_main END!!!
======NICCON Init Finish!!=========
====== Network Ready 8======
======WSD Init Finish!!=========
Вроде прошился, но безрезультатно.
Может кто знает как зайти в режим pROBE? Или это он и есть?
