Добавлено: Чт ноя 24, 2011 9:23 am
В общем привезли из области аппартат после криворуких прошивальщиков. Подробности не известны.- Код: выделить все
Boot&Mon. CheckSum OK!
[ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...
CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000638C
} /* Checksum End
Checksum Fail!!, original checksum = 0x0000A5A5, checksum = 0x0000638C
CHKSUM
{
check sum start address : 40060000, count : 00014FFE
check sum : 0000A5A5
} /* Checksum End
Checksum OK!!
finish copy image to the RAM
===> Now program restarted on the RAM to program flash
jump to 0x40060000
Flash Data Download Address : 0x40100000
===============================
Start flash_writer
===============================
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG :
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40100000)
-------------------------
Samsung OTG, 2006
Link ID : [00000000]
-------------------------
Drv "design ware core" USB download<HS><HS>
Насколько я понимаю не правильная контрольная сумма, тоесть похожу прошивка не на тот серийник.
При попытке залить оригинальную версию прошивки выдаёт:
- Код: выделить все
pROBE+> fl
Upgrade Flash ROM Image
FlashCheckSum
{
check sum start address : 40060000, count : 00014FFE
check sum : 0000A5A5
} /* Checksum End
==> Now program restarted on the RAM to program flash ROM(0x40060000)
jump to 0x40060000
Flash Data Download Address : 0x40100000
===============================
Start flash_writer
===============================
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG :
Can not find sig
----------- Display Dcache Status ------------
Control register = 0x000510F8
Icahe : ON
Dcahe : OFF
MMU : OFF
Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40100000)
-------------------------
Samsung OTG, 2006
Link ID : [00000000]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 92 bytes
[[4194424 Bytes received]] - Complete Downloading
} /* Download End */
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00400000
model : 0x05000041
flash type : 0x00020002
image type : 0x00000000
temp_buf : $KER
SIG : $KER
FlashCheckSum
{
check sum start address : 4010001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End
Source Checksum is valid
New F/W Version : 3000108
[Error] orginal image uncompress error -3
Downloaded Image is not Valid
Reset Target and Run Flash Writing Program Again