T.E.S.T.C.O.P.Y. • Просмотр темы - canon E248-0001

canon E248-0001

Неисправности и пути их решения.

Модератор: vetal

Прилепить пост

Сообщение makeda » Чт июл 17, 2014 4:37 pm

попался аппарат санон image runner 1133 if на дисплее ошибка E248-0001 кто-нибудь знает как ее скинуть, по аналогии ExecuteCopier >Function>Clear > Rcoll но блин я не нахожу ничего такого в менюшки ste_na fix-x
Аватар пользователя
makeda   
Тонерный Шаман

Прилепить пост

Сообщение makeda » Чт июл 17, 2014 5:06 pm

все победил вместе с pc-porta посидели покумекали итого заходим в тех меню голова 2,8 голова далее Execute COPIER>FUNCTION>CLEAR>RCON

За это сообщение автора makeda поблагодарил:
kvg
Рейтинг: 2.7%
 
Аватар пользователя
makeda   
Тонерный Шаман

Прилепить пост

Сообщение makeda » Ср июл 30, 2014 9:04 am

а может кто-нибудь случаем знает как откалибровать сее чудо)

Добавлено спустя 3 часа 24 минуты 21 секунду:
вроде разобрался нашел мануал от аналога


After replacing CIS units:
1) Check that there is no problem with the setting values written on the service label.
2) Close the ADF, and execute the following service mode. If it results in NG, execute it again after turning OFF and then ON the power.
- COPIER > FUNCTION > CCD > CL-AGC (CIS light intensity adjustment (color))
- COPIER > FUNCTION > CCD > BW-AGC (CIS light intensity adjustment (B&W))
3) After executing the following service mode (a), check the value automatically set with the following service mode (b), and write it in the service label.
(a) COPIER > FUNCTION > INSTALL > STRD-POS (executing automatic detection of the reading position at DF stream reading)
(b) COPIER > ADJUST > ADJ-XY > STRD-POS (adjusting the reading position at DF stream reading)
4) Place a blank paper on the Copyboard Glass, and execute white level adjustment in the following service mode.
- COPIER > FUNCTION > CCD > DF-WLVL1 (white level adjustment [copyboard scan])
- COPIER > FUNCTION > CCD > DF-WLVL3 (white level adjustment B&W [copyboard scan])
Next, place the same blank paper on the DF and execute the following service mode.
- COPIER > FUNCTION > CCD > DF-WLVL2 (white level adjustment [DF scan])
- COPIER > FUNCTION > CCD > DF-WLVL4 (white level adjustment B&W [DF scan])
If it results in NG, execute it again after turning OFF and then ON the power.


честно скомуниздино с STARTCOPY
Аватар пользователя
makeda   
Тонерный Шаман


Вернуться в Принтеры, МФУ, факсы, копиры формата A4

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 207

вверх
вниз
x

#{title}

#{text}