Добавлено: Ср фев 04, 2015 10:46 am Seeksys
Не работает USB на МФУ Samsung SCX-4824.При подключении МФУ по USB к компу пишет неудалось опознать устройство (VID 0000, PID 0000)
По WEB интерфейсу МФУ работает.
Выполнены :
1. Сброс всех настроек
2. Включение/выключение USB порта через WEB интерфейс
3. Диагностирована эл схема подключения по USB:
- защитные диоды, резисторы - иправны.
- Прошелся по чипу ISP1761 (контроллер USB) исследованы каналы USB D+, D- путем сравнения сопротивлений между тремя портами,на корпус и плюс - ОК.
так же на этом чипе присутсвует питание, генерация и т.д.
4. Подключил терминалку:
Log cтарта
Скрытый текст + POWER ON Booting... Press any key to execute Monitor Program within 1 sec... New kernel was found... CHKSUM { check sum start address : 00040000, count : 00440000 check sum : 0000A5A5 } /* Checksum End Checksum OK!! Find Compressed Kernel Kernel UnZip Done!! jump to 0x40B00000 Check PowerOn Mode PBA Port  ( GPIO3In - 0xED6740DE, GPIOIn - 0xFFFFA5DF ) ################### Normal Mode Start##########################AUTH1X_IF_InsertQueueData : 4050C170 AUTH1X_IF_IsWiredPortEnable : 4050BE08 |
Режим Debug on в pROBE+
Скрытый текст + pROBE+> debug on ------------------------------------------------[DIAG] : Debug ON (Magic ID = 0x24444F4E) ------------------------------------------------New kernel was found... CHKSUM { check sum start address : 00040000, count : 00440000 check sum : 0000A5A5 } /* Checksum End Checksum OK!! Find Compressed Kernel Kernel UnZip Done!! jump to 0x40B00000BOOT Debug is Enabled!! ------- ARM Control Coprocessor --------Control register = 0x 510ff MMU : ON Icahe : ON Dcahe : ON ------------------------------------------<<ROOT START>> Installed Memory = 128MB ================================== Check remained memory in region #0 rnid : 0x0 Remained RN#0 region : 0x357a00 - 3504640 ================================== ######################################################## Total installed Memory Size is 0x08000000 [128 MB] ######################################################## CM : gulFixedSegStartAddr =0x41980000, gulFixedSegEndAddr = 0x48000000 $FIL 0x 400000 0x41980000 $S2E 0x 100 0x41d80000 $MCT 0x 200 0x41d80100 $UEV 0x 100000 0x41d80300 $RJL 0x 800 0x41e80300 $RJ2 0x fc00 0x41e80b00 $JCB 0x 11b800 0x41e90700 $JC2 0x a0000 0x41fabf00 $MIV 0x 500 0x4204bf00 0x 0 0x 0 $CJL 0x 7d00 0x4204c400 $MJL 0x 20000 0x42054100 $Con 0x 100 0x42074100 $END 0x 10 0x42074200 0x 0 0x42074210 0x 0 0x42074210 HPVC_Initialize() RipZLib Driver is Installed successfully RipZLib Driver ISR is registered successfully IPDMA DRV OSAL_CreateTask:input name CENW, Task Number 2, TaskID 130000 OSAL_CreateTask:input name NVMT, Task Number 3, TaskID 160000 OSAL_CreateTask:input name NVMD, Task Number 4, TaskID 180000 [SM]CheckBackupMem() NVRAM Check : 0, DRAM Check : 2, FM Check : 1 OSAL_CreateTask:input name BBCbHandle, Task Number 5, TaskID 210000 [BB]NF Block = 2, SF Block = 3 Check Address = 0x730322c4 Check PowerOn Mode PBA Port ( GPIO3In - 0xED6540DE, GPIOIn - 0xFFFFA5DF ) ################### Normal Mode Start########################## OSAL_CreateTask:input name FFDR, Task Number 6, TaskID 240000 [SFLASH] Recovery Start - List[0]:[SFLASH:\FAXBACK][9][10] OK - List[1]:[SFLASH:\JOB][10][10] OK - List[2]:[SFLASH:\FAX][12][10] OK [SFLASH] Recovery End [SFLASH] Mount Success OSAL_CreateTask:input name AppTmMgr, Task Number 7, TaskID 270000 OSAL_CreateTask:input name JMT0, Task Number 8, TaskID 2b0000 OSAL_CreateTask:input name JMT1, Task Number 9, TaskID 2d0000 OSAL_CreateTask:input name JMT5, Task Number 10, TaskID 2f0000 OSAL_CreateTask:input name JMT6, Task Number 11, TaskID 310000 OSAL_CreateTask:input name JMT7, Task Number 12, TaskID 330000 OSAL_CreateTask:input name JMT8, Task Number 13, TaskID 350000 OSAL_CreateTask:input name JMT9, Task Number 14, TaskID 370000 OSAL_CreateTask:input name JSTask, Task Number 15, TaskID 3c0000 OSAL_CreateTask:input name JSSPTask, Task Number 16, TaskID 420000 OSAL_CreateTask:input name JSDGTask, Task Number 17, TaskID 440000 OSAL_CreateTask:input name MAA, Task Number 18, TaskID 470000 ************** Fault History CompEntry ************** OSAL_CreateTask:input name FHTK, Task Number 19, TaskID 490000 OSAL_CreateTask:input name PJLT, Task Number 20, TaskID 4d0000 OSAL_CreateTask:input name PJLU, Task Number 21, TaskID 4f0000 OSAL_CreateTask:input name CPCS, Task Number 22, TaskID 510000 OSAL_CreateTask:input name CPCF, Task Number 23, TaskID 530000 OSAL_CreateTask:input name CRCP, Task Number 24, TaskID 550000 5MSec Callback is registered.... 0x40b10ba4 5Msec is Already Started... Currtnt time before fix : 2015-02-03[03] 20:03:05 Currtnt time : 2015-02-03[03] 20:03:05 ############# Fault History Task Start ############# OSAL_CreateTask:input name CMIB, Task Number 25, TaskID 5e0000 OSAL_CreateTask:input name CNJI, Task Number 26, TaskID 600000 OSAL_CreateTask:input name CALT, Task Number 27, TaskID 630000 OSAL_CreateTask:input name CJI, Task Number 28, TaskID 660000 OSAL_CreateTask:input name CSTS, Task Number 29, TaskID 680000 OSAL_CreateTask:input name CSTM, Task Number 30, TaskID 690000 OSAL_CreateTask:input name CS2A, Task Number 31, TaskID 750000 OSAL_CreateTask:input name CPSU, Task Number 32, TaskID 770000 OSAL_CreateTask:input name MSCD, Task Number 33, TaskID 7b0000 OSAL_CreateTask:input name MNT0, Task Number 34, TaskID 7e0000 OSAL_CreateTask:input name MNT1, Task Number 35, TaskID 810000 OSAL_CreateTask:input name MNT2, Task Number 36, TaskID 840000 OSAL_CreateTask:input name MNT3, Task Number 37, TaskID 870000 OSAL_CreateTask:input name MNT4, Task Number 38, TaskID 8a0000 OSAL_CreateTask:input name MNT5, Task Number 39, TaskID 8d0000 OSAL_CreateTask:input name FJI, Task Number 40, TaskID 910000 OSAL_CreateTask:input name FAXT, Task Number 41, TaskID 940000 OSAL_CreateTask:input name FAXD, Task Number 42, TaskID 970000 OSAL_CreateTask:input name ImT0, Task Number 43, TaskID 9b0000 OSAL_CreateTask:input name ImT1, Task Number 44, TaskID 9d0000 OSAL_CreateTask:input name ImT2, Task Number 45, TaskID 9f0000 OSAL_CreateTask:input name ImT3, Task Number 46, TaskID a10000 OSAL_CreateTask:input name ImT4, Task Number 47, TaskID a30000 OSAL_CreateTask:input name ImT5, Task Number 48, TaskID a50000 OSAL_CreateTask:input name ImT6, Task Number 49, TaskID a70000 OSAL_CreateTask:input name ImT7, Task Number 50, TaskID a90000 OSAL_CreateTask:input name ImT8, Task Number 51, TaskID ab0000 OSAL_CreateTask:input name ImT9, Task Number 52, TaskID ad0000 OSAL_CreateTask:input name Im10, Task Number 53, TaskID af0000 OSAL_CreateTask:input name Im11, Task Number 54, TaskID b10000 OSAL_CreateTask:input name Im12, Task Number 55, TaskID b30000 OSAL_CreateTask:input name Im13, Task Number 56, TaskID b50000 OSAL_CreateTask:input name Im14, Task Number 57, TaskID b70000 OSAL_CreateTask:input name PSC1, Task Number 58, TaskID c60000 OSAL_CreateTask:input name PSC2, Task Number 59, TaskID c80000 OSAL_CreateTask:input name ES, Task Number 60, TaskID cb0000 OSAL_CreateTask:input name REND, Task Number 61, TaskID cd0000 OSAL_CreateTask:input name PM, Task Number 62, TaskID d00000 OSAL_CreateTask:input name PM2, Task Number 63, TaskID d30000 OSAL_CreateTask:input name RLS, Task Number 64, TaskID d50000 OSAL_CreateTask:input name EM, Task Number 65, TaskID da0000 Intialize PageCnt...!!! Tick Start ::>> 231 OSAL_CreateTask:input name PAGECNT, Task Number 66, TaskID dc0000 Start Load All Crum for EEPROM OSAL_CreateTask:input name ScnEngineH, Task Number 67, TaskID df0000 OSAL_CreateTask:input name RING, Task Number 68, TaskID e10000 OSAL_CreateTask:input name DIAL, Task Number 69, TaskID e30000 OSAL_CreateTask:input name PMOD, Task Number 70, TaskID e50000 OSAL_CreateTask:input name PMGR, Task Number 71, TaskID e70000 OSAL_CreateTask:input name RDB_TASK, Task Number 72, TaskID ec0000 OSAL_CreateTask:input name RDP_TASK, Task Number 73, TaskID ee0000 OSAL_CreateTask:input name RJI, Task Number 74, TaskID f10000 OSAL_CreateTask:input name UIDM, Task Number 75, TaskID f30000 <EM:0> Start of PageCnt Task [PageCnt] WM!! [PageCnt] Crum_ProcessPreRx Start! [PageCnt] PageCnt_ActivateCRUM return[1] OSAL_CreateTask:input name UIEN, Task Number 76, TaskID f90000 RipZLib Driver:Create and Added Device to DM(Handle=1092477928) NICBridge_UnzipImage() : Start ZLib Driver:Call control(411de3d8) NICBridge_UnzipImage() : malloc for Zlib is done ZLib Driver:Call control(411de3d8) [ZLIB_UNZIP:7] ulDestAddr :0x40300000, ulDestSize :0xe59ff054, ulSrcAddr :0x480000, ulSrcSize :0x380000 [ZLIB_UNZIP:5193948] ulResult :0x0 NICBridge_UnzipImage() : uncompressing is done // Result[0] => 0 : success, other : fail NICBridge_UnzipImage() : mem free for Zlib is done NICBridge_UnzipImage() : End OSAL_CreateTask:input name Rip, Task Number 77, TaskID ff0000(CopyNVvars): sizeof (NVVars) =0x1f80 [PageCnt] PageCnt_ActivateCRUM return[1] RipZLib Driver:Create and Added Device to DM(Handle=1092478112) Rip : Initialize map table size(32) MM : Create Segment OSAL_CreateTask:input name CSWS, Task Number 78, TaskID 10c0000 ============================================================================================== Display MST = [SegID] [Handle] [SegSize] [BlockSize] [TotBNO] [TAllocBNO] [TFreeBNO] [TLargeBNO] [VM] [Start] [End]= $RJL 0 0x 7c0 64 31 0 31 31 0 0x41e80300 0x41e80ac0 $RJ2 1 0x fc00 64 1008 0 1008 1008 0 0x41e80b00 0x41e90700 $JCB 2 0x 11b800 64 18144 0 18144 18144 0 0x41e90700 0x41fabf00 $JC2 3 0x a0000 64 10240 0 10240 10240 0 0x41fabf00 0x4204bf00 $CJL 4 0x 7d00 64 500 0 500 500 1 0x4204c400 0x42054100 $Con 5 0x 100 64 4 0 4 4 0 0x42074100 0x42074200 $MJL 6 0x 20000 64 2048 0 2048 2048 0 0x42054100 0x42074100 $BBD 16 0x 3e90 1 16016 16016 0 0 0 0x42074210 0x420780a0 $BBC 17 0x b4 1 180 180 0 0 0 0x420780a0 0x42078154 $BBR 18 0x 5000 1 20480 20480 0 0 0 0x42078154 0x4207d154 $ATM 19 0x 18c0 64 99 10 89 89 1 0x4207d180 0x4207ea40 $IPC 20 0x fc0 64 63 0 63 63 0 0x4207ea80 0x4207fa40 $JSQ 21 0x 63c0 64 399 0 399 399 1 0x4207fa80 0x42085e40 $CDM 22 0x 3c3c0 64 3855 0 3855 3855 0 0x4208 [PageCnt] PageCnt_ActivateCRUM return[1]5e80 0x420c2240 $PJL 23 0x a28 1 2600 2576 24 24 0 0x420c2254 0x420c2c7c $PSU 24 0x 45380 1 283520 283456 64 64 0 0x420c2c7c 0x42107ffc $Msc 25 0x 1fffc0 64 32767 0 32767 32767 0 0x42108000 0x42307fc0 $ImT 26 0x b7ffc0 64 188415 0 188415 188415 0 0x42308000 0x42e87fc0 $PRB 27 0x 9c140 64 9989 9986 3 3 0 0x42e88000 0x42f24140 $SPL 28 0x 63940 64 6373 6372 1 1 0 0x42f24180 0x42f87ac0 $BND 29 0x 58bc0 64 5679 0 5679 5679 0 0x42f87b00 0x42fe06c0 $PSC 30 0x cc0 64 51 0 51 51 1 0x42fe0700 0x42fe13c0 $PCB 31 0x fffc0 64 16383 0 16383 16383 1 0x42fe1400 0x430e13c0 $Scn 32 0x f7c7c0 [PageCnt] WM!! 64 253727 6830 246897 246897 0 0x430e1400 0x4405dbc0 $RBR 33 0x 800 1 2048 0 2048 2048 0 0x4405dbf0 0x4405e3f0 $RPR 34 0x 32000 1 204800 0 204800 204800 0 0x4405e3f0 0x440903f0 $RPS 35 0x 888 1 2184 0 2184 2184 0 0x440903f0 0x44090c78 $NIC 36 0x 1fffc0 64 32767 0 32767 32767 0 0x44090c80 0x44290c40 $ADD 37 0x 740 64 29 0 29 29 0 0x44290c80 0x442913c0 $HIP 49 0x 3c78840 64 990753 0 990753 990753 0 0x44386fc0 0x47fff800 ========================================================================== Country Other than Isreal [Rip]Loading PCL6 by Uzip ZLib Driver:Call control(411de490) [ZLIB_UNZIP:0] ulDestAddr :0x40080000, ulDestSize :0xe59ff054, ulSrcAddr :0xac0000, ulSrcSize :0x40000 [ZLIB_UNZIP:482332] ulResult :0x0 Id(9) sign(aa55) addr(400a711c) endvar(401252c4) start(400f5c1c) version(PCL6 5.93 03-21-2009) [Rip]Loading PCL5e by Uzip ZLib Driver:Call control(411de490) [ZLIB_UNZIP:1] ulDestAddr :0x40080000, ulDestSize :0xe59ff054, ulSrcAddr :0xb00000, ulSrcSize :0x74000 [ZLIB_UNZIP:751900] ulResult :0x0 Id(1) sign(aa55) addr(400f68a4) endvar(4015e0a4) start(4013791c) version(PCL5e 5.92 02-12-2009) [Rip]Loading QPDL by Uzip ZLib Driver:Call control(411de490) [ZLIB_UNZIP:3] ulDestAddr :0x40080000, ulDestSize :0xe59ff054, ulSrcAddr :0xb74000, ulSrcSize :0x6000 [ZLIB_UNZIP:44596] ulResult :0x0 Id(16) sign(aa55) addr(4008380c) endvar(4008d744) start(4008ae34) version(SPL 5.32 01-03-2008) [CM_IF_MemoryInfo] Extended Memory[0] TotalSize[0x8000000] opcode = 0x0231 index = 507 [SEHn]SHADING - Start!!!AUTH1X_IF_InsertQueueData : 4050C170 AUTH1X_IF_IsWiredPortEnable : 4050BE08 [SEHn]SHADING - Start!!! [SEHn]SHADING - Start!!! [SEHn]SHADING - Start!!! [SEHn]SHADING - Start!!! [SEHn]SHADING - Start!!! ================================== Check remained memory in region #0 rnid : 0x0 Remained RN#0 region : 0x210a00 - 2165248 ================================== <EM:10000> [PageCnt] CRUM_MSG_RXALLITEM [PageCnt] [2]Pseudo Print Mode?? ___ 0 Entering Crum_ProcessPreRx [PageCnt] PageCnt_ActivateCRUM return[1] [PageCnt] PageCnt_ActivateCRUM return[1] [PageCnt] PageCnt_ActivateCRUM return[1] [80509f] [PageCnt] GPIO1 Data = 0x82509f [PageCnt] ----> (Init Toner mode TRUE)[PageCnt] WM!! EC : Power Save <Sleep> S:10393 M:173 <EM:30000> |
При подключении/отключении МФУ по USB в терминал ничего не выводится.
Вопросы:
1.Емеются ли какие-то комманды для дигностики USB портов ?
2.Как принудительно из терминала запустить USB ? (USB start, USB reset - непрокатывают)
3.Можно ли переназначить номер порта для работы с PC (контроллер имеет 3 порта, хотя используется только один)
