Здравствуйте, уважаемые форумчане и знатоки своего дела. У меня не получается реанимировать аппарат после неудачной прошивки.
Стоял на работе аппарат, после покупки с версией 09, сотрудники умные товарищи умудрились в него запихать фикс от 07 версии. Потом попытались его оживить и залили еще что-то, Вообщем убили. Теперь пытаюсь реанимировать этот аппарат. Подключил аппарат к Jtag( провод от телефона Siemens C55), вроде бы выдаёт ответ правильно. Пытаюсь прошить оригинальной версией прошивки и получаю [Error] orginal image uncompress error -3. Пробовал все версии оригинальной прошивок от 09 до 13. Внизу приведен лог терминала. Пожалуйста помогите восстановить аппарат.
Скрытый текст + - Код: выделить все
Boot&Mon. CheckSum OK! [SFLASH_InitFLASH][NG] [ POWER ON Booting... ] Press any key to execute Monitor Program within 1 sec... Kernel Data Read Start From Serial Flash New kernel was found...
CHKSUM { check sum start address : 41000000, count : 001B0000 check sum : 0000ADA5 } /* Checksum End
Checksum Fail!!, original checksum = 0x0000A5A5, checksum = 0x0000ADA5 [SFLASH_InitFLASH][NG]
CHKSUM { check sum start address : 40060000, count : 00014FFE check sum : 0000A5A5 } /* Checksum End
Checksum OK!! finish copy image to the RAM
===> Now program restarted on the RAM to program flash jump to 0x40060000 Flash Data Download Address : 0x40100000
=============================== Start flash_writer =============================== [SFLASH_InitFLASH][NG] verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00000000 model : 0x00000000 flash type : 0x00000000 image type : 0x00000000 temp_buf : SIG : Can not find sig ----------- Display Dcache Status ------------ Control register = 0x000510F8 Icahe : ON Dcahe : OFF MMU : OFF
Download Image from PC { Ready to download from Parallel/Usb/Serial (0x40100000) ------------------------- Samsung OTG, 2006 Link ID : [00000000] ------------------------- Drv "design ware core" USB download<HS><HS>
Boot&Mon. CheckSum OK!
[SFLASH_InitFLASH][NG] [ POWER ON Booting... ]
Press any key to execute Monitor Program within 1 sec...
<CPU:375Mhz RAM:166Mhz SysClk:125Mhz DDR2>
---------------------------------------------------------------- START-UP MODE : Monitor Program Boot into pROBE+ like stand-alone mode [Type 'help' to see command info.] Version : Ver.1.20 (BlueMT) 2011-04-27 ---------------------------------------------------------------- Do you want to download from external port?[N] : n
pROBE+> nnnnnnnnnnnnnnnnnnnn invalid command format
pROBE+> fl
Upgrade Flash ROM Image [SFLASH_InitFLASH][NG]
FlashCheckSum { check sum start address : 40060000, count : 00014FFE check sum : 0000A5A5 } /* Checksum End
==> Now program restarted on the RAM to program flash ROM(0x40060000) jump to 0x40060000 Flash Data Download Address : 0x40100000
=============================== Start flash_writer =============================== [SFLASH_InitFLASH][NG] verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00000000 model : 0x00000000 flash type : 0x00000000 image type : 0x00000000 temp_buf : SIG : Can not find sig ----------- Display Dcache Status ------------ Control register = 0x000510F8 Icahe : ON Dcahe : OFF MMU : OFF
Download Image from PC { Ready to download from Parallel/Usb/Serial (0x40100000) ------------------------- Samsung OTG, 2006 Link ID : [00000000] ------------------------- Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200> Image includes PJL(0000001B) -> Waste 92 bytes [[4194424 Bytes received]] - Complete Downloading
} /* Download End */ verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00400000 model : 0x05000041 flash type : 0x00020002 image type : 0x00000000 temp_buf : $KER SIG : $KER
FlashCheckSum { check sum start address : 4010001C, count : 00400000 check sum : 0000A5A5 } /* Checksum End
Source Checksum is valid New F/W Version : 3000113 [Error] orginal image uncompress error -3 Downloaded Image is not Valid Reset Target and Run Flash Writing Program Again
|