Добавлено: Пт сен 28, 2012 3:39 pm Deimos
добрый день! принесли аппарат друзья, после прошивки всетит зелёным глазом но действий никаких нет! гипер терминал пишет при загрузке -
Скрытый текст + Boot&Mon. CheckSum OK! [ POWER ON Booting... ] Press any key to execute Monitor Program within 1 sec... Kernel Data Read Start From Serial Flash New kernel was found... CHKSUM { check sum start address : 42F00000, count : 00440000 check sum : 0000CB34 } /* Checksum End Checksum Fail!!, original checksum = 0x0000A5A5, checksum = 0x0000CB34 CHKSUM { check sum start address : 40060000, count : 00014FFE check sum : 0000A5A5 } /* Checksum End Checksum OK!! finish copy image to the RAM ===> Now program restarted on the RAM to program flash jump to 0x40060000 Flash Data Download Address : 0x40100000 =============================== Start flash_writer =============================== verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00000000 model : 0x00000000 flash type : 0x00000000 image type : 0x00000000 temp_buf : SIG : Can not find sig  ------- Display Dcache Status --------Control register = 0x000510F8 Icahe : ON Dcahe : OFF MMU : OFF Download Image from PC { Ready to download from Parallel/Usb/Serial (0x40100000)<FS><HS><FS><HS> |
при попытке принудительной прошивки пишет:
Скрытый текст + Boot&Mon. CheckSum OK! [ POWER ON Booting... ] Press any key to execute Monitor Program within 1 sec... <CPU:375Mhz RAM:166Mhz SysClk:125Mhz DDR2> ------------------------------------------------------------START-UP MODE : Monitor Program Boot into pROBE+ like stand-alone mode [Type 'help' to see command info.] Version : Ver.1.05 (BLUE_BIRD_W) 2011-04-27 ------------------------------------------------------------Do you want to download from external port?[N] : n pROBE+> fl Upgrade Flash ROM Image FlashCheckSum { check sum start address : 40060000, count : 00014FFE check sum : 0000A5A5 } /* Checksum End ==> Now program restarted on the RAM to program flash ROM(0x40060000) jump to 0x40060000 Flash Data Download Address : 0x40100000 =============================== Start flash_writer =============================== verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00000000 model : 0x00000000 flash type : 0x00000000 image type : 0x00000000 temp_buf : SIG : Can not find sig ------- Display Dcache Status --------Control register = 0x000510F8 Icahe : ON Dcahe : OFF MMU : OFF Download Image from PC { Ready to download from Parallel/Usb/Serial (0x40100000)<FS><HS><FS><HS> Download destination Address : 0x40100000 Image includes PJL(0000001B) -> Waste 92 bytes [[8388636 Bytes received]] - Complete Downloading } /* Download End */ verify_Image : 0x40100000 i_header->pul_start_addr : 0x00000000 i_header->ul_count : 0x00800000 model : 0x03000051 flash type : 0x00030002 image type : 0x00000000 temp_buf : $KER SIG : $KER FlashCheckSum { check sum start address : 4010001C, count : 00800000 check sum : 0000A5A5 } /* Checksum End Source Checksum is valid New F/W Version : 3000106 error  alid code lengths set[Error] orginal image uncompress error -3 Downloaded Image is not Valid Reset Target and Run Flash Writing Program Again |
может кто сталкивался прошу помощи!
