T.E.S.T.C.O.P.Y. • Просмотр темы - Дебаг

Дебаг

Проблемы с ПК и периферийным оборудованием

Модератор: Stelt

Правила форума
Просьба ознакомиться с Правилами форума.
Также большая просьба, картинки выкладывать или в Галерею, или прикрепляйте их к своим сообщениям.
Ссылки в темах на сторонние фотохостинги (кроме вконтакте) заблокированы.

Прилепить пост

Сообщение GSA » Пт сен 30, 2011 3:37 pm

marinad писал(а):осталось 3 проводочка - дебаг-кабель готов :)


Резисторы все-же по 50..100 Ом лучше б навесить на Tx и Rx, а то разница в напряжениях может быть и бо-бо случится, а так я сам таким же пользуюсь. Все работает и макросы грузятся.
Ремонтирую то, чем пользуюсь. Пользуюсь тем, что ремонтирую.
Аватар пользователя
GSA   
Держал тонер в руках
  • Не в сети

Прилепить пост

Сообщение Artur » Пт мар 16, 2012 3:10 pm

Собрал шнурок от телефооного дата кабеля/Nokia 3310/ по моему, на выходе там было всего 3 провода, синий белый и черный.Черный кинул на землю,синий и белый методом тыка определил TX и Rx.Питание кинул через усб +5 на hyper Vcc принтера.Запустил hyper Terminal полет нормальный.захожу а dROBE, пишу fl , жму ентер,запускаю прошивку.Идет процесс прошивки. Но после завершения,аппарат не выходит в готовность,как я понял по серийнику мфу не прошился(серийник не совпадает с номером на крышке,до этого его скорей всего клонировали)..В чем дело уважаемые форумчане,аппарат SCX-3200

Код: выделить все
Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ POWER ON  Booting... ]

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...

CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000A5A5
} /* Checksum End

Checksum OK!!
Kernel Data Read End
 Find Compressed Kernel
 Kernel UnZip Done!!
jump to 0x40080000
 ramsize= 406BFFFF, gsbsize = 40501204, FreeMemPtr = 40500548, FreeMemStart = 40
500548
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 Model Code : SCX3200
 Main Kernel F/W Version : V3.00.01.08
 Main Kernel F/W Date : OCT-18-2010
 Check PowerOn Mode PBA Port ---- ( GPIO3In - 0xadeff, GPIOIn - 0xef )
DRAM:>
 ################### Normal Mode Start##########################

Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ POWER ON  Booting... ]

Press any key to execute Monitor Program within 1 sec...

<CPU:375Mhz RAM:166Mhz SysClk:125Mhz DDR2>

----------------------------------------------------------------
START-UP MODE : Monitor Program
  Boot into pROBE+ like stand-alone mode
  [Type 'help' to see command info.]
  Version : Ver.1.18 (BlueMT) 2010-10-15
----------------------------------------------------------------
Do you want to download from external port?[N] : n

pROBE+> nnnnnnnnnnnnfl
invalid command format


pROBE+> fl

Upgrade Flash ROM Image
[SFLASH_InitFLASH][NG]

FlashCheckSum
{
check sum start address : 40060000, count : 00014FFE
check sum : 0000A5A5
} /* Checksum End

==> Now program restarted on the RAM to program flash ROM(0x40060000)
jump to 0x40060000
Flash Data Download Address : 0x40100000

===============================
    Start flash_writer
===============================
[SFLASH_InitFLASH][NG]
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00000000
model : 0x00000000
flash type : 0x00000000
image type : 0x00000000
temp_buf :
SIG :
Can not find sig
----------- Display Dcache Status ------------
    Control register       = 0x000510F8
    Icahe : ON
    Dcahe : OFF
    MMU   : OFF

Download Image from PC
{
Ready to download from Parallel/Usb/Serial (0x40100000)
-------------------------
Samsung OTG, 2006
Link ID   : [00000000]
-------------------------
Drv "design ware core" USB download<HS><HS><EPB_RX 0x00000200>
Image includes PJL(0000001B) -> Waste 92 bytes
[[4194424 Bytes received]] - Complete Downloading

} /* Download End */
verify_Image : 0x40100000
i_header->pul_start_addr : 0x00000000
i_header->ul_count : 0x00400000
model : 0x05000041
flash type : 0x00020002
image type : 0x00000000
temp_buf : $KER
SIG : $KER

FlashCheckSum
{
check sum start address : 4010001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End

Source Checksum is valid
 New F/W Version : 3000108
 Current F/W Version : 3000108
This is a valid image.!!!!

[[[[[ Flash Writing : BANK[0] 0x00000000]]]]]
flash_start_addr : 0x00000000
flash_end_addr   : 0x00400000
flash_data_size  : 0x00400000
src_image_start_addr : 0x4010001C
0x00004000 words - 0x00010000 bytes programmed(2 percent : 0x003F0000)
0x00004000 words - 0x00010000 bytes programmed(4 percent : 0x003E0000)
0x00004000 words - 0x00010000 bytes programmed(5 percent : 0x003D0000)
0x00004000 words - 0x00010000 bytes programmed(7 percent : 0x003C0000)
0x00004000 words - 0x00010000 bytes programmed(8 percent : 0x003B0000)
0x00004000 words - 0x00010000 bytes programmed(10 percent : 0x003A0000)
0x00004000 words - 0x00010000 bytes programmed(11 percent : 0x00390000)
0x00004000 words - 0x00010000 bytes programmed(13 percent : 0x00380000)
0x00004000 words - 0x00010000 bytes programmed(15 percent : 0x00370000)
0x00004000 words - 0x00010000 bytes programmed(16 percent : 0x00360000)
0x00004000 words - 0x00010000 bytes programmed(18 percent : 0x00350000)
0x00004000 words - 0x00010000 bytes programmed(19 percent : 0x00340000)
0x00004000 words - 0x00010000 bytes programmed(21 percent : 0x00330000)
0x00004000 words - 0x00010000 bytes programmed(22 percent : 0x00320000)
0x00004000 words - 0x00010000 bytes programmed(24 percent : 0x00310000)
0x00004000 words - 0x00010000 bytes programmed(25 percent : 0x00300000)
0x00004000 words - 0x00010000 bytes programmed(27 percent : 0x002F0000)
0x00004000 words - 0x00010000 bytes programmed(29 percent : 0x002E0000)
0x00004000 words - 0x00010000 bytes programmed(30 percent : 0x002D0000)
0x00004000 words - 0x00010000 bytes programmed(32 percent : 0x002C0000)
0x00004000 words - 0x00010000 bytes programmed(33 percent : 0x002B0000)
0x00004000 words - 0x00010000 bytes programmed(35 percent : 0x002A0000)
0x00004000 words - 0x00010000 bytes programmed(36 percent : 0x00290000)
0x00004000 words - 0x00010000 bytes programmed(38 percent : 0x00280000)
0x00004000 words - 0x00010000 bytes programmed(40 percent : 0x00270000)
0x00004000 words - 0x00010000 bytes programmed(41 percent : 0x00260000)
0x00004000 words - 0x00010000 bytes programmed(43 percent : 0x00250000)
0x00004000 words - 0x00010000 bytes programmed(44 percent : 0x00240000)
0x00004000 words - 0x00010000 bytes programmed(46 percent : 0x00230000)
0x00004000 words - 0x00010000 bytes programmed(47 percent : 0x00220000)
0x00004000 words - 0x00010000 bytes programmed(49 percent : 0x00210000)
0x00004000 words - 0x00010000 bytes programmed(50 percent : 0x00200000)
0x00004000 words - 0x00010000 bytes programmed(52 percent : 0x001F0000)
0x00004000 words - 0x00010000 bytes programmed(54 percent : 0x001E0000)
0x00004000 words - 0x00010000 bytes programmed(55 percent : 0x001D0000)
0x00004000 words - 0x00010000 bytes programmed(57 percent : 0x001C0000)
0x00004000 words - 0x00010000 bytes programmed(58 percent : 0x001B0000)
0x00004000 words - 0x00010000 bytes programmed(60 percent : 0x001A0000)
0x00004000 words - 0x00010000 bytes programmed(61 percent : 0x00190000)
0x00004000 words - 0x00010000 bytes programmed(63 percent : 0x00180000)
0x00004000 words - 0x00010000 bytes programmed(65 percent : 0x00170000)
0x00004000 words - 0x00010000 bytes programmed(66 percent : 0x00160000)
0x00004000 words - 0x00010000 bytes programmed(68 percent : 0x00150000)
0x00004000 words - 0x00010000 bytes programmed(69 percent : 0x00140000)
0x00004000 words - 0x00010000 bytes programmed(71 percent : 0x00130000)
0x00004000 words - 0x00010000 bytes programmed(72 percent : 0x00120000)
0x00004000 words - 0x00010000 bytes programmed(74 percent : 0x00110000)
0x00004000 words - 0x00010000 bytes programmed(75 percent : 0x00100000)
0x00004000 words - 0x00010000 bytes programmed(77 percent : 0x000F0000)
0x00004000 words - 0x00010000 bytes programmed(79 percent : 0x000E0000)
0x00004000 words - 0x00010000 bytes programmed(80 percent : 0x000D0000)
0x00004000 words - 0x00010000 bytes programmed(82 percent : 0x000C0000)
0x00004000 words - 0x00010000 bytes programmed(83 percent : 0x000B0000)
0x00004000 words - 0x00010000 bytes programmed(85 percent : 0x000A0000)
0x00004000 words - 0x00010000 bytes programmed(86 percent : 0x00090000)
0x00004000 words - 0x00010000 bytes programmed(88 percent : 0x00080000)
0x00004000 words - 0x00010000 bytes programmed(90 percent : 0x00070000)
0x00004000 words - 0x00010000 bytes programmed(91 percent : 0x00060000)
0x00004000 words - 0x00010000 bytes programmed(93 percent : 0x00050000)
0x00004000 words - 0x00010000 bytes programmed(94 percent : 0x00040000)
0x00004000 words - 0x00010000 bytes programmed(96 percent : 0x00030000)
0x00004000 words - 0x00010000 bytes programmed(97 percent : 0x00020000)
0x00004000 words - 0x00010000 bytes programmed(99 percent : 0x00010000)
0x00004000 words - 0x00010000 bytes programmed(100 percent : 0x00000000)

FlashCheckSum
{
check sum start address : 4010001C, count : 00400000
check sum : 0000A5A5
} /* Checksum End

=>check sum is valid

Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ WATCH DOG RESET  Booting... ]

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...

CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000A5A5
} /* Checksum End

Checksum OK!!
Kernel Data Read End
 Find Compressed Kernel
 Kernel UnZip Done!!
jump to 0x40080000
 ramsize= 406BFFFF, gsbsize = 40501204, FreeMemPtr = 40500548, FreeMemStart = 40
500548
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 Model Code : SCX3200
 Main Kernel F/W Version : V3.00.01.08
 Main Kernel F/W Date : OCT-18-2010
 Check PowerOn Mode PBA Port ---- ( GPIO3In - 0xadeff, GPIOIn - 0xef )
DRAM:>
 ################### Normal Mode Start##########################
------------------------------------------------------------------------------
Data Access Abort
                                   Running:  ****** ISR ******
------------------------------------------------------------------------------
CPSR = 60000093 (nZCv If ARM SVC)      SP =40502BE8 LR =402904C8
R0 =0CD6CA6D R1 =00000000 R2 =000000E1 R3 =0000000F R4 =40502C04
R5 =40502C00 R6 =019FC9ED R7 =65E15AE8 R8 =40358A60 R9 =40358AE8
R10=00000000 R11=40376FC4 R12=00000000
PC =4028529C



Assertion failed: 0, file excepthndl.c, line 799

<<<Doassert_InformToPRN>>>

Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ WATCH DOG RESET  Booting... ]

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...

CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000A5A5
} /* Checksum End

Checksum OK!!
Kernel Data Read End
 Find Compressed Kernel
 Kernel UnZip Done!!
jump to 0x40080000
 ramsize= 406BFFFF, gsbsize = 40501204, FreeMemPtr = 40500548, FreeMemStart = 40
500548
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 Model Code : SCX3200
 Main Kernel F/W Version : V3.00.01.08
 Main Kernel F/W Date : OCT-18-2010
 Check PowerOn Mode PBA Port ---- ( GPIO3In - 0xadef8, GPIOIn - 0xef )
DRAM:>
 ################### Normal Mode Start##########################
------------------------------------------------------------------------------
Data Access Abort
                                   Running:  ****** ISR ******
------------------------------------------------------------------------------
CPSR = 60000093 (nZCv If ARM SVC)      SP =40502BE8 LR =402904C8
R0 =0CD6CA6D R1 =00000000 R2 =000000E1 R3 =0000000F R4 =40502C04
R5 =40502C00 R6 =019FC9ED R7 =65E15AE8 R8 =40358A60 R9 =40358AE8
R10=00000000 R11=40376FC4 R12=00000000
PC =4028529C



Assertion failed: 0, file excepthndl.c, line 799

<<<Doassert_InformToPRN>>>

Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ WATCH DOG RESET  Booting... ]

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...

CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000A5A5
} /* Checksum End

Checksum OK!!
Kernel Data Read End
 Find Compressed Kernel
 Kernel UnZip Done!!
jump to 0x40080000
 ramsize= 406BFFFF, gsbsize = 40501204, FreeMemPtr = 40500548, FreeMemStart = 40
500548
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 Model Code : SCX3200
 Main Kernel F/W Version : V3.00.01.08
 Main Kernel F/W Date : OCT-18-2010
 Check PowerOn Mode PBA Port ---- ( GPIO3In - 0xadede, GPIOIn - 0xef )
DRAM:>
 ################### Normal Mode Start##########################
------------------------------------------------------------------------------
Data Access Abort
                                   Running:  ****** ISR ******
------------------------------------------------------------------------------
CPSR = 60000093 (nZCv If ARM SVC)      SP =40502BE8 LR =402904C8
R0 =0CD6CA6D R1 =00000000 R2 =000000E1 R3 =0000000F R4 =40502C04
R5 =40502C00 R6 =019FC9ED R7 =65E15AE8 R8 =40358A60 R9 =40358AE8
R10=00000000 R11=40376FC4 R12=00000000
PC =4028529C



Assertion failed: 0, file excepthndl.c, line 799

<<<Doassert_InformToPRN>>>

Boot&Mon. CheckSum OK!

[SFLASH_InitFLASH][NG]
[ WATCH DOG RESET  Booting... ]

Press any key to execute Monitor Program within 1 sec...
Kernel Data Read Start From Serial Flash
New kernel was found...

CHKSUM
{
check sum start address : 41000000, count : 001B0000
check sum : 0000A5A5
} /* Checksum End

Checksum OK!!
Kernel Data Read End
 Find Compressed Kernel
 Kernel UnZip Done!!
jump to 0x40080000
 ramsize= 406BFFFF, gsbsize = 40501204, FreeMemPtr = 40500548, FreeMemStart = 40
500548
 <<< Reelase Mode >>>
<<<LogMsg_PrintOff>>>
 Model Code : SCX3200
 Main Kernel F/W Version : V3.00.01.08
 Main Kernel F/W Date : OCT-18-2010
 Check PowerOn Mode PBA Port ---- ( GPIO3In - 0xade0e, GPIOIn - 0xef )
DRAM:>
 ################### Normal Mode Start##########################
Аватар пользователя
Artur   
Осматривается
  • Не в сети

Прилепить пост

Сообщение Дормидонт_Генрихович » Пт мар 16, 2012 7:22 pm

залейте оригинальную 8 версию
говорю правду в глаза...
Аватар пользователя
Дормидонт_Генрихович   
Умеет пользоваться Parts Catalog

Пред.

Вернуться в Компьютеры и периферия

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 3

вверх
вниз
x

#{title}

#{text}