T.E.S.T.C.O.P.Y. • Просмотр темы - xp-103 мигают все три индикатора синхронно

xp-103 мигают все три индикатора синхронно

Ремонт, обслуживание, фотопечать, СНПЧ.

Модераторы: KOT, Женька 116

Прилепить пост

Сообщение alexpotap » Вс фев 28, 2016 1:42 pm

Принесли после "мастера",с неустановленной узкой крышкой (между принтером и сканером в задней части которая доступ к шлейфам закрывает) сказали что только сброс памперса делал после этого
печатает только с компа индикаторы мигают синхронно, на нажатия кнопок не реагирует(кроме питания), снпч капсульная, отчет принт хелпа:
Время первичной инициализации 2013/01/31
Код последней фатальной ошибки принтера 1 0x0A CR load position excess load error. CR motor failure, CR unit drive mechanism overload (paper jam, foreign object, change lever failure), cable disconnection, main board failure (motor driver failure).
Код последней фатальной ошибки принтера 2 0x01 CR PID excess load error. CR motor failure, CR unit drive mechanism overload, some part may be detached (paper guide upper assy, cap assy), tooth skip of the CR timing belt, improper tension of the CR timing belt, cable disconnection, main board failure (motor driver failure).
Код последней фатальной ошибки принтера 3 0x89 Insufficient light error. Sensor failure (PIS board installation failure, contaminated sensor), abnormal sensor output (break of FFC during printer operation, PIS board failure), unable to accurately detect where the fault detection plate is because too much diffused light from outside is shed on the sensor (when used outdoors or near the window where direct sunlight comes in), ink cartridge failure (contaminated/damaged prism).
Код последней фатальной ошибки принтера 4 0x89 Insufficient light error. Sensor failure (PIS board installation failure, contaminated sensor), abnormal sensor output (break of FFC during printer operation, PIS board failure), unable to accurately detect where the fault detection plate is because too much diffused light from outside is shed on the sensor (when used outdoors or near the window where direct sunlight comes in), ink cartridge failure (contaminated/damaged prism).
Код последней фатальной ошибки принтера 5 0x89 Insufficient light error. Sensor failure (PIS board installation failure, contaminated sensor), abnormal sensor output (break of FFC during printer operation, PIS board failure), unable to accurately detect where the fault detection plate is because too much diffused light from outside is shed on the sensor (when used outdoors or near the window where direct sunlight comes in), ink cartridge failure (contaminated/damaged prism).
Код последней фатальной ошибки сканера 1 0x20 LED lightning error. CIS Module failure, foreign object, scanner housing upper failure (white standard pattern is dirty), main board failure.
Аватар пользователя
alexpotap   
Осматривается
  • Не в сети

Прилепить пост

Сообщение makeda » Вс фев 28, 2016 4:35 pm

В сканер копать надо. Так как не работает только этот узел
Аватар пользователя
makeda   
Тонерный Шаман

Прилепить пост

Сообщение rfinfyrf » Пн фев 29, 2016 1:04 pm

5 0x89 Insufficient light error. - почисти оптический датчик в принтере или замени,(тот который на просвет работает) стоит на роликах выходных, или еще вариант черную полоску в каретку попробовать наклеит.
Аватар пользователя
rfinfyrf   
Собрал картридж
  • Не в сети

Прилепить пост

Сообщение alexpotap » Пн фев 29, 2016 1:45 pm

с датчиком попробую. полоску клеил, не помогает
Аватар пользователя
alexpotap   
Осматривается
  • Не в сети


Вернуться в Принтеры струйные

Кто сейчас на форуме

Сейчас этот форум просматривают: нет зарегистрированных пользователей и гости: 53

вверх
вниз
x

#{title}

#{text}